Морате бити пријављени да
-
- Генератори: cнага од 500 В, фреквенција 150-400 кХз
- Генератори: Снага 1,2 - 2,4 кВ, фреквенција 150 - 400 кХз
- Генератори: cнага 4,2 - 10 кВ, фреквенција 150 - 400 кХз
- Генератори: cнага 10 - 15 кВ, фреквенција 50 - 150 кХз
- Генератори: cнага 30-45 кВ, фреквенција 50-150 кХз
- Генератори: cнага 65-135 кВ, фреквенција 50-150 кХз
- Генератори: cнага 180-270 кВ, фреквенција 50-150 кХз
- Генератори: cнага 20-35-50 кВ, фреквенција 15-45 кХз
- Генератори: cнага 75-150 кВ, фреквенција 15-45 кХз
- Генератори: cнага 200-500 кВ, фреквенција 15-45 кХз
- Генератори: cнага 20-50 кВ, фреквенција 5-15 кХз
- Генератори: cнага 75-200 кВ, фреквенција 5-15 кХз
- Генератори: cнага 250-500 кВ, фреквенција 5-15 кХз
- Генератори: cнага 75-250 кВ, фреквенција 2-6 кХз
- Генератори: cнага 300-500 кВ, фреквенција 2-6 кХз
-
- Генератори серије ЦКС, фреквенција: 50-120кХз, снага: 5-25кВ
- Генератори СВС серије, фреквенција: 15-30кХз, снага: 25-260кВ
- Генератори (пећи) за обликовање и ковање МФС серије, фреквенција: 0,5-10кХз, снага: 80-500кВ
- МФС пећи за топљење, фреквенција: 0,5-10кХз, снага: 70-200кВ
- Генератори UHT серије, фреквенција: 200-400кХз, снага: 10-160кВ
What is the purpose of induction heating generators?
Induction generators convert alternating current to a higher frequency current to then deliver it to the operating coil, allowing an electromagnetic field to be created within it.
When a workpiece is placed in this field, eddy currents are induced in the workpiece. The friction caused by these currents generates precise, clean, non-contact heat. Depending on the power and on the frequency, we are able to determine the heating rate and the penetration depth of the heat.
A water cooling system is usually required to cool the work coil and induction system.
Operating frequency
The size of the workpiece and the heating application dictate the operating frequency of the induction heating equipment. In general, the larger the workpiece, the lower the frequency and the smaller the workpiece, the higher the frequency.
The operating frequency is determined by the tank circuit capacitance, coil inductance and workpiece material properties.
Power requirements
The power required to heat the workpiece depends on:
- The mass of your work piece;
- The material properties of your work piece;
- The temperature increase you require;
- The heating time required to meet your process needs;
- The effectiveness of the field owing to the coil design;
- Any heat losses during the heating process.
Once the power required to heat the workpiece is determined, the appropriate induction heating equipment can be selected, taking into account the coupling efficiency of the coil.