Преобразователь для измерения постоянного и переменного тока DHR-C10 и DHR-C420 Ipn100..1000A
  • Преобразователь для измерения постоянного и переменного тока DHR-C10 и DHR-C420 Ipn100..1000A

Фотографії призначені тільки для інформаційних цілей. Подивитися специфікацію продукту

please use latin characters

Виробник: LEM

Перетворювачі для вимірювання серії DC та змінної DHR

The transducer for the electronic measurement of DC [&] distorted AC waveform currents, with galvanic isolation between the primary circuit (power) and the secondary circuit (measurement). True RMS 0-10V voltage output.

Features
• VFD and SCR waveforms current measurement
• True RMS output
• Panel mounting
• Eliminates insertion loss
• Isolated plastic case recognized according to UL94-V0

Advantages:
• Large aperture for cable up to Ø32mm
• High isolation between primary and secondary circuits
• Easy installation

Applications
• VFD Controlled Loads VFD output indicates how the motor and attached load are operating.
• SCR Controlled Loads Acurate measurement of phase angle fired or burst fired (time proportioned) SCRs. Current measurement gives faster response than temperature measurement.
• Switching Power Supplies and Electronic Ballasts
True RMS sensing is the most accurate way to measure power supply or ballast input power.

Warning:
Transmitters should be installed and serviced after power off. The service technician should be authorized to repair the installation of this type of equipment. Users should follow safety regulations against electric shock.

Isolation characteristics
Vb - Rated isolation voltage rms
1000V
according to the standard IEC 61010-1 and with the following conditions:
 
• Reinforced isolation
  
 
• Over voltage category
CAT III
 
• Pollution degree
PD2
 
• Heterogeneous field
  
Vd - Rms voltage for AC isolation test, 50 Hz, 1min
5kV
dCp - Creepage distance
11mm
Dci - Clearance distance
11mm
CTI - Comparative tracking index (Group I)
600

Table. Electrical data

TypePrimary Nominal DC [&] AC Current IPN SKPrimary AC Current Max. Peak Value
Ip [A]		Output voltage analogueRL Load resistanceIC Current consumptionOutput voltage limitation (0 - 10 V)Overload capability (Ampere Turns)
DHR 100 Cl0 100 600 0-10 > lOkΩ 30mA <14V 30000 A.z.
DHR 200 C10 200 600
DHR 300 Cl0 300 1000
DHR 400 Cl0 400 1000
DHR 500 Cl0 500 1800
DHR 600 Cl0 600 1800
DHR 1000 Cl0 1000 1800
DHR 100 C420 100 600 4-20 < 300Ω 30mA + Iwy <25mA 30000 A.z.
DHR 200 C420 200 600
DHR 300 C420 300 1000
DHR 400 C420 400 1000
DHR 500 C420 500 1800
DHR 600 C420 600 1800
DHR 1000 C420 1000 1800

Table. Performance data

 DHR-C10DHR-C420
x Accuracy @IPN TA = 25°C (excluding offset)
 < ±1% IPN < ±1% IPN
εLLinearity error (1% of IPN .. ± IPN)
 < ±1% IPN < ±1% IPN
VCE/ICE Electrical offset voltage,TA =25°C
 < ±1% IPN 4mA
VOT Temperature coefficient VCE (-20 do 60°C)
( -40 do 70°C)

±1mV/K

±2mV/K

±1,6µA/K

±3,2 µA/K
TCeG Dryft temperaturowy wzmocnienia (% odczytu)
 ±0,1%/K ±0,1%/K
Tr Response time to 90 % of IPN step
 <150ms <150ms
F Frequency bandwidth (± 1 dB
 0, 20...6000Hz 0, 20...6000Hz

Table. General data

TA Surrounding operating temperature -40 do 70°C
TS Surrounding storage temperature -40 do 85°C
M Mass 260g
IP Protection degree IP20

Transfer characteristics
Dimensions[mm]
Connection
Mechanical characteristics
General tolerance:
±1mm.
Primary aperture:
032mm,
Panel mounting
4 holes ø4,6mm
Distance between holes
70mm i 78mm (jakna rysunku).
For panel mounting, use M4 screws (not supplied) with
appropriate length to panel´s thickness, and tighten to
0.75Nm +/-20% torque.

Менше
Читати більше

Відправити запит

Ви зацікавлені у цьому продукті? Вам потрібна додаткова інформація або індивідуальні розцінки?

Зв'яжіться з нами

ZAPYTAJ O PRODUKT close
Wiadomość wysłana poprawnie.
ZAPYTAJ O PRODUKT close
Przeglądaj

Додати до списку бажань

Ви повинні увійти в систему

The transducer for the electronic measurement of DC [&] distorted AC waveform currents, with galvanic isolation between the primary circuit (power) and the secondary circuit (measurement). True RMS 0-10V voltage output.

Features
• VFD and SCR waveforms current measurement
• True RMS output
• Panel mounting
• Eliminates insertion loss
• Isolated plastic case recognized according to UL94-V0

Advantages:
• Large aperture for cable up to Ø32mm
• High isolation between primary and secondary circuits
• Easy installation

Applications
• VFD Controlled Loads VFD output indicates how the motor and attached load are operating.
• SCR Controlled Loads Acurate measurement of phase angle fired or burst fired (time proportioned) SCRs. Current measurement gives faster response than temperature measurement.
• Switching Power Supplies and Electronic Ballasts
True RMS sensing is the most accurate way to measure power supply or ballast input power.

Warning:
Transmitters should be installed and serviced after power off. The service technician should be authorized to repair the installation of this type of equipment. Users should follow safety regulations against electric shock.

Isolation characteristics
Vb - Rated isolation voltage rms
1000V
according to the standard IEC 61010-1 and with the following conditions:
 
• Reinforced isolation
  
 
• Over voltage category
CAT III
 
• Pollution degree
PD2
 
• Heterogeneous field
  
Vd - Rms voltage for AC isolation test, 50 Hz, 1min
5kV
dCp - Creepage distance
11mm
Dci - Clearance distance
11mm
CTI - Comparative tracking index (Group I)
600

Table. Electrical data

TypePrimary Nominal DC [&] AC Current IPN SKPrimary AC Current Max. Peak Value
Ip [A]		Output voltage analogueRL Load resistanceIC Current consumptionOutput voltage limitation (0 - 10 V)Overload capability (Ampere Turns)
DHR 100 Cl0 100 600 0-10 > lOkΩ 30mA <14V 30000 A.z.
DHR 200 C10 200 600
DHR 300 Cl0 300 1000
DHR 400 Cl0 400 1000
DHR 500 Cl0 500 1800
DHR 600 Cl0 600 1800
DHR 1000 Cl0 1000 1800
DHR 100 C420 100 600 4-20 < 300Ω 30mA + Iwy <25mA 30000 A.z.
DHR 200 C420 200 600
DHR 300 C420 300 1000
DHR 400 C420 400 1000
DHR 500 C420 500 1800
DHR 600 C420 600 1800
DHR 1000 C420 1000 1800

Table. Performance data

 DHR-C10DHR-C420
x Accuracy @IPN TA = 25°C (excluding offset)
 < ±1% IPN < ±1% IPN
εLLinearity error (1% of IPN .. ± IPN)
 < ±1% IPN < ±1% IPN
VCE/ICE Electrical offset voltage,TA =25°C
 < ±1% IPN 4mA
VOT Temperature coefficient VCE (-20 do 60°C)
( -40 do 70°C)

±1mV/K

±2mV/K

±1,6µA/K

±3,2 µA/K
TCeG Dryft temperaturowy wzmocnienia (% odczytu)
 ±0,1%/K ±0,1%/K
Tr Response time to 90 % of IPN step
 <150ms <150ms
F Frequency bandwidth (± 1 dB
 0, 20...6000Hz 0, 20...6000Hz

Table. General data

TA Surrounding operating temperature -40 do 70°C
TS Surrounding storage temperature -40 do 85°C
M Mass 260g
IP Protection degree IP20

Transfer characteristics
Dimensions[mm]
Connection
Mechanical characteristics
General tolerance:
±1mm.
Primary aperture:
032mm,
Panel mounting
4 holes ø4,6mm
Distance between holes
70mm i 78mm (jakna rysunku).
For panel mounting, use M4 screws (not supplied) with
appropriate length to panel´s thickness, and tighten to
0.75Nm +/-20% torque.

Менше
Читати більше