Adhesivo de silicona conductora
Adhesivo de silicona conductora

Las fotos son solo para fines informativos. Ver especificaciones de producto

please use latin characters

Fabricante: SOLIANI

Adhesivo de silicona conductora

Elastomer Conductive Adhesive

The conductive adhesive is supplied as a paste that does not require mixing. It achieves its properties at room temperature.

Conductive Adhesive Parameters

  • electrically conductive
  • non-corrosive
  • single component – no mixing required
  • excellent adhesion to various substrates

Instructions for Use

The surface to be bonded must be clean, dry, and degreased with common solvents used for substrate cleaning, such as acetone, methyl ethyl ketone, xylene, and isopropyl alcohol. The adhesive should be applied directly to the cleaned surface. If the product is to be used as a binder, it should be evenly spread on both surfaces and held pressed until it sets. The full conductive and sealing properties of the conductive adhesive are achieved after the full drying time.

Safety

WARNING! Contact of the adhesive with eyes or skin may be irritating. In such cases, excess adhesive should be wiped off with a dry cloth or towel and hands washed with industrial cleaning products designed for this purpose (e.g., paste).

Cleaning

Uncured conductive silicone adhesive can be removed with, for example, acetone.

Storage

The storage period for both unopened and opened adhesive is one (1) year from the shipping date, provided that the products are stored in a dry, tightly closed, original container below 23°C (73.4°F).

Standard Containers

  • 0.5 fl. oz. (metal tube)
  • 1.0 fl. oz. (metal tube or cartridge)
  • 2.5 fl. oz. (cartridge)
  • 10.3 fl. oz. (cartridge)

Technical Table

  Unit NG
nickel-graphite		 SPG
silver-glass		 SNK
silver-nickel		 SPA
silver-aluminum		 SPC
silver-copper		 S
pure silver
Color   Dark gray Light brown Brown Blue Dark brown Brown
Consistency   Thick paste Thick paste Thick paste Thick paste Thick paste Thick paste
Specific Gravity (typical) g/cm3 2.3 1.82 3.58 1.86 3.58 4.2
Hardness (+/-5) Shore A 65 70 75 68 70 65
Resistance (Max) Ohm -cm 0.1 0.01 0.008 0.01 0.008 0.005
Shear Strength (minimum) PSI 70 120 120 175 200 225
Operating Temperature °C -0.25 -0.25 -0.25 -0.25 -0.25 -0.25
Tack Time Min 15 15 15 15 15 15
Viscosity Time Min 45 90 90 90 90 90
Time after which bonded element can be used hours 24-24 24-24 24-24 24-24 24-24 24-24
Full Cure Time hours 72-144 72-144 72-144 72-144 72-144 72-144
Tensile Strength (minimum) PSI 250 250 250 200 250 250
Elongation (minimum) % 30 35 35 35 40 35



Order Example

SOL - O8 - XX - 2.5
XX - NG, SPG, SNK, SPA, SPC, S (choice available).

In our offer, you will also find stainless steel enclosures.

Menos
Lee mas

Envíe una consulta

¿Estás interesado en este producto? ¿Necesita información adicional o precios individuales?

Contacta con nosotras
SOLICITA EL PRODUCTO close
Gracias por enviar tu mensaje. Responderemos lo antes posible.
SOLICITA EL PRODUCTO close
Vistazo
enviar una consulta

Añadir a la lista de deseos

Usted debe estar conectado

Elastomer Conductive Adhesive

The conductive adhesive is supplied as a paste that does not require mixing. It achieves its properties at room temperature.

Conductive Adhesive Parameters

  • electrically conductive
  • non-corrosive
  • single component – no mixing required
  • excellent adhesion to various substrates

Instructions for Use

The surface to be bonded must be clean, dry, and degreased with common solvents used for substrate cleaning, such as acetone, methyl ethyl ketone, xylene, and isopropyl alcohol. The adhesive should be applied directly to the cleaned surface. If the product is to be used as a binder, it should be evenly spread on both surfaces and held pressed until it sets. The full conductive and sealing properties of the conductive adhesive are achieved after the full drying time.

Safety

WARNING! Contact of the adhesive with eyes or skin may be irritating. In such cases, excess adhesive should be wiped off with a dry cloth or towel and hands washed with industrial cleaning products designed for this purpose (e.g., paste).

Cleaning

Uncured conductive silicone adhesive can be removed with, for example, acetone.

Storage

The storage period for both unopened and opened adhesive is one (1) year from the shipping date, provided that the products are stored in a dry, tightly closed, original container below 23°C (73.4°F).

Standard Containers

  • 0.5 fl. oz. (metal tube)
  • 1.0 fl. oz. (metal tube or cartridge)
  • 2.5 fl. oz. (cartridge)
  • 10.3 fl. oz. (cartridge)

Technical Table

  Unit NG
nickel-graphite		 SPG
silver-glass		 SNK
silver-nickel		 SPA
silver-aluminum		 SPC
silver-copper		 S
pure silver
Color   Dark gray Light brown Brown Blue Dark brown Brown
Consistency   Thick paste Thick paste Thick paste Thick paste Thick paste Thick paste
Specific Gravity (typical) g/cm3 2.3 1.82 3.58 1.86 3.58 4.2
Hardness (+/-5) Shore A 65 70 75 68 70 65
Resistance (Max) Ohm -cm 0.1 0.01 0.008 0.01 0.008 0.005
Shear Strength (minimum) PSI 70 120 120 175 200 225
Operating Temperature °C -0.25 -0.25 -0.25 -0.25 -0.25 -0.25
Tack Time Min 15 15 15 15 15 15
Viscosity Time Min 45 90 90 90 90 90
Time after which bonded element can be used hours 24-24 24-24 24-24 24-24 24-24 24-24
Full Cure Time hours 72-144 72-144 72-144 72-144 72-144 72-144
Tensile Strength (minimum) PSI 250 250 250 200 250 250
Elongation (minimum) % 30 35 35 35 40 35



Order Example

SOL - O8 - XX - 2.5
XX - NG, SPG, SNK, SPA, SPC, S (choice available).

In our offer, you will also find stainless steel enclosures.

Menos
Lee mas
Comentarios (0)