Moulded Component Technology
  • Moulded Component Technology

Photos are for informational purposes only. View product specification

please use latin characters

Manufacturer: TC SHIELDING

Cast conductive gaskets

The technique of moulding conductive elastomers has a wide range of benefits. This process allows T C Shielding to manufacture components that have a very accurate tolerance requirement. Below is a list of its major advantages:

  • Odd and 3D shaped components are easily made.
  • Accurate tolerances can be held.
  • Small products are easy to manufacture.
  • Product can be adhesive backed (dependent upon moulding type).
  • Silicones and fluorosilicones plus wide range of conductive fillers.
 

Comparative Properties - Moulded Materials

General Description
EcE Material Reference (Type) 1A 1B 1D 1F 1G 1I
             
Elastomer Type (Sil - Silicone, F/Sil - Fluorosilicone) Sil Sil Sil Sil Sil Sil
Filler Material Ag/Ni Ag/Cu Ag/Al Carbon Ag Ag/Glass
Colour Tan Tan Tan Black Tan Tan
Electrical Properties Tol Test Method            
Volume Resistivity (ohm.cm) Max   0,005 0,005 0,008 9,000 0,002 0,005
Shielding Effectiveness (dB)
200 KHz (H-Field)
  MIL-G-83528
MIL 285
70 70 70 30 70 55
100 MHz (E-Field)   105 115 110 65 115 95
500 MHz (E-Field)   105 115 105 60 115 95
2 GHz (Plane Wave)   100 115 100 40 115 95
10 GHz (Plane Wave)   100 115 100 30 115 95
Physical Properties
Specific Gravity (g/cm∆) ±5% ASTM D-792 3,71 3,32 2,19 1,19 3,20 "2.00
75
1.25"
Hardness (Shore A) ± 5 ASTM D-2240 70 75 70 70 75
Tensile Strength (MPa) Min ASTM D-412 1,25 1,25 1,25 5,00 1,25
Elongation (%) Min ASTM D-412 100 100 100 150 100 100
Compression Set (%) Max ASTM D-395 30 30 30 20 30 30
Upper Operating Temperature (°C) -   160 125 160 160 160 160
Lower Operating Temperature (°C) - ASTM D-1329 -50 -50 -50 -50 -50 -50

General Description
EcE Material Reference (Type) 1J 1J/8 2A 2B 2D 2J
    Non Flam        
Elastomer Type (Sil - Silicone, F/Sil - Fluorosilicone) Sil Sil F/Sil F/Sil F/Sil F/Sil
Filler Material Ni/Gr Ni/Gr Ag/Ni Ag/Cu Ag/Al Ni/Gr
Colour szary szary Tan Tan Green Green
Electrical Properties Tol Test Method  
Volume Resistivity (ohm.cm) Max   0,05 "0.050- 0,005 0,005 0,01 0,05
0.100"
Shielding Effectiveness (dB)   MIL-G-83528            
200 KHz (H-Field) MIL 285 70 70 75 75 70 70
100 MHz (E-Field)     95 95 110 110 110 100
500 MHz (E-Field)     90 90 110 120 105 100
2 GHz (Plane Wave)     90 90 105 120 100 100
10 GHz (Plane Wave)     90 90 100 120 100 100
Physical Properties
Specific Gravity (g/cm∆) ±5% ASTM D-792 2,45 2,3 4,6 5 2,7 3,25
Hardness (Shore A) ± 5 ASTM D-2240 80 75 80 75 70 80
Tensile Strength (MPa) Min ASTM D-412 2 1,4 1,25 1,25 0,55 0,75
Elongation (%) Min ASTM D-412 150 125 100 100 100 100
Compression Set (%) Max ASTM D-395 30 30 30 30 30 30
Upper Operating Temperature (°C) -   160 160 160 125 160 160
Lower Operating Temperature (°C) - ASTM D-1329 -50 -50 -50 -55 -55 -55

Standard connector products

Rear Mounting Jam Nut Receptacle ‘O’ Rings

Standardowe przewodzące uszczelki odlewane

Shell size MIL C 38999 MIL C 26482 MIL C 81511 d1 Tol d1 ± d2
TC REF TC REF mm mm mm
6 1 - 14.00 0.13 1.78
8 2 - 17.16 0.13 1.78
8 - 3 18.77 0.13 1.78
9 4 - 20.35 0.15 1.78
10 - 5 21.95 0.15 1.78
11+12 6 - 25.12 0.15 1.78
13+14 7 7 28.30 0.15 1.78
15+16 8 8 31.47 0.15 1.78
17+18 9 9 34.65 0.15 1.78
19+20 10 - 37.77 0.15 2.62
21+22 11 - 40.95 0.25 2.62
23+24 12 - 44.12 0.25 2.62

Order example

MA - XX - XXX
Example: MA

MA - Moulded Ring
3A - Silver Aluminium/Silicone
001 - Shell size

Cost Effective Alternative To Conductive Moulded O-Rings

T.C.Shielding have developed a range of extruded/jointed O-Rings that offer a cost effective alternative to traditionally moulded items with added benefits, and compatible tolerancing. The following are benefits of this new process.

  • Low tooling cost
  • Reduced production scrap rate
  • Advantage of hollow forms which help to reduce compression force
  • Zero flash on profile
  • Compatible tolerancing
  • Shorter lead times
  • Minimum ID of 18.00mm

Below is a comparison between moulded and jointed tolerances

Moulded O-ring
ID = 25.12+/-0.15
Section = 1.78+/-0.08
Developed Lenght= 84.04/84.98

Ext./Jointed O-ring
ID = 25.12+/-0.16
Cross section= 1.78+/-0.10
Developed Length= 84.00/85.00

 

Send an inquiry

Are you interested in this product? Do you need additional information or individual pricing?

Contact us

ASK FOR THE PRODUCT close
Message sent successfully.
ASK FOR THE PRODUCT close
Browse

Add to Wishlist

You must be logged in

The technique of moulding conductive elastomers has a wide range of benefits. This process allows T C Shielding to manufacture components that have a very accurate tolerance requirement. Below is a list of its major advantages:

  • Odd and 3D shaped components are easily made.
  • Accurate tolerances can be held.
  • Small products are easy to manufacture.
  • Product can be adhesive backed (dependent upon moulding type).
  • Silicones and fluorosilicones plus wide range of conductive fillers.
 

Comparative Properties - Moulded Materials

General Description
EcE Material Reference (Type) 1A 1B 1D 1F 1G 1I
             
Elastomer Type (Sil - Silicone, F/Sil - Fluorosilicone) Sil Sil Sil Sil Sil Sil
Filler Material Ag/Ni Ag/Cu Ag/Al Carbon Ag Ag/Glass
Colour Tan Tan Tan Black Tan Tan
Electrical Properties Tol Test Method            
Volume Resistivity (ohm.cm) Max   0,005 0,005 0,008 9,000 0,002 0,005
Shielding Effectiveness (dB)
200 KHz (H-Field)
  MIL-G-83528
MIL 285
70 70 70 30 70 55
100 MHz (E-Field)   105 115 110 65 115 95
500 MHz (E-Field)   105 115 105 60 115 95
2 GHz (Plane Wave)   100 115 100 40 115 95
10 GHz (Plane Wave)   100 115 100 30 115 95
Physical Properties
Specific Gravity (g/cm∆) ±5% ASTM D-792 3,71 3,32 2,19 1,19 3,20 "2.00
75
1.25"
Hardness (Shore A) ± 5 ASTM D-2240 70 75 70 70 75
Tensile Strength (MPa) Min ASTM D-412 1,25 1,25 1,25 5,00 1,25
Elongation (%) Min ASTM D-412 100 100 100 150 100 100
Compression Set (%) Max ASTM D-395 30 30 30 20 30 30
Upper Operating Temperature (°C) -   160 125 160 160 160 160
Lower Operating Temperature (°C) - ASTM D-1329 -50 -50 -50 -50 -50 -50

General Description
EcE Material Reference (Type) 1J 1J/8 2A 2B 2D 2J
    Non Flam        
Elastomer Type (Sil - Silicone, F/Sil - Fluorosilicone) Sil Sil F/Sil F/Sil F/Sil F/Sil
Filler Material Ni/Gr Ni/Gr Ag/Ni Ag/Cu Ag/Al Ni/Gr
Colour szary szary Tan Tan Green Green
Electrical Properties Tol Test Method  
Volume Resistivity (ohm.cm) Max   0,05 "0.050- 0,005 0,005 0,01 0,05
0.100"
Shielding Effectiveness (dB)   MIL-G-83528            
200 KHz (H-Field) MIL 285 70 70 75 75 70 70
100 MHz (E-Field)     95 95 110 110 110 100
500 MHz (E-Field)     90 90 110 120 105 100
2 GHz (Plane Wave)     90 90 105 120 100 100
10 GHz (Plane Wave)     90 90 100 120 100 100
Physical Properties
Specific Gravity (g/cm∆) ±5% ASTM D-792 2,45 2,3 4,6 5 2,7 3,25
Hardness (Shore A) ± 5 ASTM D-2240 80 75 80 75 70 80
Tensile Strength (MPa) Min ASTM D-412 2 1,4 1,25 1,25 0,55 0,75
Elongation (%) Min ASTM D-412 150 125 100 100 100 100
Compression Set (%) Max ASTM D-395 30 30 30 30 30 30
Upper Operating Temperature (°C) -   160 160 160 125 160 160
Lower Operating Temperature (°C) - ASTM D-1329 -50 -50 -50 -55 -55 -55

Standard connector products

Rear Mounting Jam Nut Receptacle ‘O’ Rings

Standardowe przewodzące uszczelki odlewane

Shell size MIL C 38999 MIL C 26482 MIL C 81511 d1 Tol d1 ± d2
TC REF TC REF mm mm mm
6 1 - 14.00 0.13 1.78
8 2 - 17.16 0.13 1.78
8 - 3 18.77 0.13 1.78
9 4 - 20.35 0.15 1.78
10 - 5 21.95 0.15 1.78
11+12 6 - 25.12 0.15 1.78
13+14 7 7 28.30 0.15 1.78
15+16 8 8 31.47 0.15 1.78
17+18 9 9 34.65 0.15 1.78
19+20 10 - 37.77 0.15 2.62
21+22 11 - 40.95 0.25 2.62
23+24 12 - 44.12 0.25 2.62

Order example

MA - XX - XXX
Example: MA

MA - Moulded Ring
3A - Silver Aluminium/Silicone
001 - Shell size

Cost Effective Alternative To Conductive Moulded O-Rings

T.C.Shielding have developed a range of extruded/jointed O-Rings that offer a cost effective alternative to traditionally moulded items with added benefits, and compatible tolerancing. The following are benefits of this new process.

  • Low tooling cost
  • Reduced production scrap rate
  • Advantage of hollow forms which help to reduce compression force
  • Zero flash on profile
  • Compatible tolerancing
  • Shorter lead times
  • Minimum ID of 18.00mm

Below is a comparison between moulded and jointed tolerances

Moulded O-ring
ID = 25.12+/-0.15
Section = 1.78+/-0.08
Developed Lenght= 84.04/84.98

Ext./Jointed O-ring
ID = 25.12+/-0.16
Cross section= 1.78+/-0.10
Developed Length= 84.00/85.00